|
|
|
The Productivity®Open platform provides all the great features of a standard Arduino plus the added power and reliability of an industrial controller. The processor circuit of the P1AM-100 CPU is designed to mimic the Arduino MKRZero microcontroller. The P1AM-100 is compatible with most available Arduino MKR format shields, and/or all of the industrially-hardened Productivity®Open shields, and can utilize most Arduino sketch programs found on open-source websites. The industrial-grade P1AM-100- Supports Productivity1000 input, output and specialty modules
- Supports Arduino MKR form factor shields
- UL listed CPU
- UL listed Productivity®Open branded shields
|
|
|
|
|
|
|
Brands
|
|
AutomationDirect
|
|
|
|
|
|
Open source controllers are typically based on a readily-available hardware standard and utilize openly shared programs found online in their applications. Commonly using the C++ programming language, these controllers abound in Maker and DIY communities. Industrialized open source controllers allow the same sharing of ideas and software but are hardened for the industrial environment.
The Productivity®Open platform provides all the great features of a standard Arduino plus the added power and reliability of an industrial controller.- Industrial-Grade P1AM-100 CPU (Arduino-compatible)
- Industrial-Grade Power Supplies
- Industrial-Grade Shields
- Industrial-Grade Productivity1000 I/O Modules
With the growing popularity of single-board controllers and the risks of implementing them in industrial applications, an open-source controller is needed that will hold up in the most extreme industrial conditions. Produced in conjunction with FACTS Engineering, the Productivity®Open platform combines Maker ingenuity and the proven reliability of the AutomationDirect Productivity controller family.
|
|
|
|
- The processor circuit of the P1AM-100 is designed to mimic the Arduino MKRZero microcontroller. The P1AM-100 is able to recognize most available Arduino MKR format shields, and/or all of the industrially-hardened Productivity shields, and can utilize most Arduino sketch programs found on open-source websites.
- Using the readily-available Arduino integrated development environment (IDE), the P1AM-100 is programmed using C++ code; the ProductivityBlocks graphical programming interface uses a more visual approach that simplifies coding and reduces syntax errors.
- The P1AM-100 supports the full suite of Productivity1000 I/O expansion modules, including: discrete, analog, temperature, relay, high-speed input, pulse-width-modulation
- The robust industrial power supply stage produces a regulated 5VDC output from a 24VDC input, isolating the CPU and I/O power. Use any of the field-proven Productivity1000 industrial power supply modules or other available devices wired to the terminal block connection.
|
|
|
|
|
P1AM-100 Central Processing Unit (CPU) (Arduino-Compatible)
|
|
The P1AM-100 is an industrial-grade open source CPU. It uses the Atmel SAMD21G18 microcontroller and can be programmed using Arduino IDE or ProductivityBlocks. It interfaces with all Productivity1000 Series I/O modules connected to the right side of the P1AM-100 and most Arduino MKR form factor shields connected to the left side.- Memory: 256kB Flash with 10kB used for bootloader, 32kB SRAM
- Interfaces:
- MicroB USB, Arduino MKR-compatible,
- microSD card slot for data logging (32GB max)
- User controlled LED and switch
- Programmed in C/C++ with the Arduino IDE or ProductivityBlocks
- Operating temperature 0 to 60ºC (32 to 140ºF)
- 24VDC powered
- cULus, CE agency approvals
|
|
|
|
P1AM-ETH Ethernet Shield
|
|
The P1AM-ETH is a housed Ethernet shield based on the Wiznet W5500 Ethernet Controller. It interfaces to the left side of the P1AM-100 CPU and most Arduino MKR form factor shields.- Supports hardwired TCP Protocols: TCP, UDP, ICMP, IPV4, ARP, IGMP, PPPOE
- Supports 8 independent sockets simultaneously
- Supports Power Down Mode
- Supports Wake on LAN over UDP
- Supports high-speed Serial Peripheral Interface (SPI MODE 0, 3)
- Internal 32K bytes of memory for TX/RX buffers
- 10BaseT / 100BaseTX Ethernet PHY embedded
- Supports auto negotiation (full and half duplex, 10 and 100-based)
- Does not support IP fragmentation
- 3.3 V operation with 5V I/O signal tolerance
- LED outputs (Full / Half duplex, Link, Speed, Active)
- cULus, CE agency approvals
|
|
|
|
P1AM-GPIO General Purpose Input/Output (I/O) Shield
|
|
MKR Form Factor Shield (Header Pin Breakout)
The P1AM-GPIO brings a subset of the MKR header pins to the front faceplate with an 18-position terminal block. These pins include basic overvoltage, undervoltage, and overcurrent protection. It connects to the left side of the P1AM-100 CPU and most Arduino MKR form factor shields.- cULus, CE agency approvals
|
|
|
|
P1AM-PROTO Proto Shield Kit
|
|
The P1AM-PROTO is a kit of parts that includes everything needed to make customized shields in the MKR form factor.- Custom MKR stacking headers
- PC board with 100mil (0.1 in.) grid of through-holes
- Plastic Productivity1000 form factor housing
- Footprint for 18-pin terminal block receptacle (right angle, through hole, 3.81 mm pitch) and plug for user I/O connections
- Productivity®Open overlay which can be easily cut to expose parts (LEDs, connectors, etc.) custom to the user.
|
|
|
|
P1AM-START1 Starter Kit
|
|
A convenient start to a project which will use primarily Arduino MKR Zero shields:- P1AM-100 CPU module
- P1AM-ETH shield
- P1AM-GPIO shield
- P1-4ADL2DAL-1 analog I/O module
- PSL-24-030 power supply
- Terminal blocks, AC power cord
|
|
|
|
P1AM-START2 Starter Kit
|
|
A convenient start to a project which will use primarily Productivity1000 input and output modules:- P1AM-100 CPU module
- P1-01AC power supply
- P1-08TRS relay output module
- P1-08SIM simulator input module
- Terminal blocks, AC power cord
- USB-CBL-AMICB6 USB programming cable
|
|
|
|
24 Volt (V) Direct Current (DC) Voltage Power Supply
|
|
Stand-alone DIN rail mount unit.- 24 VDC (adjustable) output
- 120/240 VAC or 125-375 VDC input
- Double isolation
|
|
|
|
P1 Power Supplies
|
|
Provides 24 VDC isolated power to the Productivity®Open platform.- P1-01AC 100-240 VAC, 16W
- P1-02AC 100-240 VAC, 26W
- P1-01DC 12-24 VDC, 16W
|
|
|
|
|
|
|
|
|
|
